The prebuilt ConnectCore image includes support for the ConnectCore Cloud Services demo.

  1. Establish a serial connection with your device

  2. Download the firmware

  3. Program the firmware

1. Establish a serial connection with your device

Open a serial connection with the device. You can use any serial terminal program such as Tera Term, Minicom, CoolTerm, or HyperTerminal.

PuTTY terminal program is not recommended due to an incompatibility with the USB/serial driver.

Open a serial connection with the following settings:

Parameter Value

Port

Serial port where the device is connected

Baud rate

115200

Data bits

8

Parity

None

Stop bits

1

Flow control

None

2. Download the firmware

Download the firmware images from the following location: https://ftp1.digi.com/support/digiembeddedyocto/4.0/r5/images/ccimx8x-sbc-pro/ccimx8x-sbc-pro-installer.zip

3. Program the firmware

Digi recommends you use the Universal Update Utility (UUU) through a USB connection to your development PC to program the images.

  1. Decompress the zip file in a directory of your choice.

  1. Download the latest Universal Update Utility (UUU), a software tool from NXP.

    UUU version should be 1.5.11 or higher.

  2. Place the uuu executable in a directory in your PATH, such as /usr/bin.

  3. Install udev rules to allow any user to run uuu to access the USB port:

    $ sudo sh -c "uuu -udev >> /etc/udev/rules.d/70-uuu.rules"
$ sudo udevadm control --reload

  1. Connect a USB type-C cable to your development PC and the other end to the target USB type-C connector.

  2. Reset the device by pressing the reset button on the board and immediately press any key in the serial terminal to stop the auto-boot process. The U-Boot bootloader prompt displays:

    U-Boot SPL dub-2020.04-r6.1 (Sep 19 2023 - 07:15:55 +0000)
Normal Boot
Trying to boot from MMC1
Primary set selected
Load image from MMC/SD 0x59c00


U-Boot dub-2020.04-r6.1 (Sep 19 2023 - 07:15:55 +0000)

CPU:   NXP i.MX8QXP RevC A35 at 1200 MHz at 33C
DRAM:  2 GiB
MCA:   HW_VER=1  FW_VER=1.01
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
In:    serial
Out:   serial
Err:   serial
Model: Digi International ConnectCore 8X SBC Pro Board.
ConnectCore 8X SOM variant 0x02: 2 GiB LPDDR4, Wi-Fi, Bluetooth, MCA, Crypto-auth
  Board version 3, ID 135
Boot:  MMC0

 BuildInfo:
  - SCFW 6638c032, SECO-FW c9de51c0, IMX-MKIMAGE 3bfcfccb, ATF e4b2dbf
  - U-Boot dub-2020.04-r6.1

flash target is MMC:0
Net:   eth0: ethernet@5b040000 [PRIME], eth1: ethernet@5b050000
Fastboot: Normal
Normal Boot
Hit any key to stop autoboot:  0
=>
    Information in the console log may vary.

  3. On the target, in U-Boot, execute the following command:

    => fastboot 1

  4. On your development PC, change to the directory where you extracted the ZIP file:

    $ cd <zip-folder>

  5. Program the image files:

    $ ./install_linux_fw_uuu.sh

  6. Once the firmware is installed, the device boots automatically. The default username is root with no password.

While the recommended boot method is eMMC, you can also boot the image from a microSD card using the *.sdcard image file on the downloaded ZIP file. See Boot from microSD card for instructions on programming a microSD card and booting from it.

You must use a microSD with a minimum capacity of 8 GB.